Installing a GPS tracking device in your automobile just isn't a complicated task, however it is essential to take safety precautions, as such the installation ought to solely be carried out by a certified Auto Electrician. Usually, it takes approximately 2 hours to set it up relying on the complexity of the vehicle’s wiring structure. GPS machine set up (fundamental set up with no gas/temperature/door sensors linked), read the following instructions. Read extra on the Do’s & Dont’s of GPS system set up at the top of this doc. Screwdriver set, Plier, Multimeter and Wire Stripper/Cutter/Crimper. Before installing the device, you want to note down International Mobile Equipment Identity (IMEI) number of the GPS tracking device and the SIM GSM number. Then insert the GPRS enabled SIM card to the system. Chances are you'll as well obtain the vehicle addition template to document car information. Then insert the GPRS enabled SIM card to the device.

You may as nicely obtain the car addition template to document automobile info. IMEI is a singular quantity to establish GSM, WCDMA, and iDEN mobile phones, satellite tv for iTagPro reviews pc phones, as well as some telematics gadgets that works as a singular identification code. This 15-digit quantity is often printed either on the underside of the GPS monitoring unit or the gadget case; you require IMEI to register the GPS tracking device on the fleet administration software program. Red wire (of GPS machine) to one finish and the ability supply of the automobile to the opposite finish of a 1Amp fuse. Secure the fuse to the instrument chord with a cable tie. Connect Black wire (-ve) on the harness to Chassis Ground (any bolt or iTagPro key finder wire with -ve energy). Connect Yellow ignition sense wire to the vehicle’s ignition supply to assist observe ignition ON/OFF events. Please consult the automobile wiring diagram to find the ignition wire.

You can verify the automobile ignition wire by measuring the vehicle’s operating voltage whereas the engine is working. Once identified, join the ignition wire to the FUSE Box with a 3M Scotchlok so that it's going to snap into place and can get it properly seated. Please refer to the connection diagram below, for an in depth view of the wires & connectivities. One of many quickest and one of the best place to mount a GPS tracking device or a GPS tracker is underneath the dashboard or an exterior location in a horizontal place with a transparent view of the sky. You may experiment with putting the tracking device at completely different locations on the automobile to find out the best reception for iTagPro reviews the desired stage of concealment. If the device has exterior iTagPro reviews GPS antenna then place the antenna underneath the dashboard or wherever handy using double-sided sticky-tape to ensure it’s firmly fastened there. Once you’ve placed the GPS tracker in the vehicle, you’re all set.

Connect the wire socket and GPS/GSM antenna (of these with exterior iTagPro reviews antenna) to the GPS machine. As soon as the gadget is powered on, both inexperienced LEDs (GPS & communication) will flash on and off whereas searching for indicators. When full sign power is achieved, both LEDs will constantly illuminate. So as to validate performance, we have to ring the GSM mobile number of the SIM. If it rings or iTagPro smart device responds with a busy observe, you may safely assume that the device is functioning correctly. If there isn't any response, iTagPro portable chances are you'll should re-insert the SIM card and examine the wiring once more. Please Log into the platform together with your credentials to make sure the system communicates with the server. Note: Ensure that the IMEI no’s & mobile no’s you updated in opposition to the autos are right. To avoid mishaps whereas set up, make sure that the car ignition is turned off earlier than initiating wire connections. It's always advisable to disconnect the suitable jumpers /connections of vehicle’s power provide during the GPS gadget set up; that is to keep away from quick circuits and iTagPro tracker wiring damages.

Be sure the wires keep disconnected while mounting/dismounting the system. Secure all wiring with Scotchlok, cable connectors, and electrical insulation tapes. Never allow any naked wiring to stay exposed; connections must be least visible. Ensure additional insulation if wires undergo a seen/exterior area, so as to avoid quick circuit/wiring damages. GPS monitoring gadgets may very well be mounted in a zone of restricted entry, so none has direct entry to the instrument. Keep connecting wires as discreetly as attainable, making it less visible and exhausting to note. For the safety of personnel, device & vehicle, keep away from connecting machine wires to the board computers (ECU) or control units. Ensure that you simply fasten wires to other wires/non-shifting elements and not to fasten near heat emitting and transferring objects as friction/heat emission could cause sparks resulting in short circuits. While connecting ignition wire confirm if it’s the actual ignition wire (power supply obtainable only when the ignition is on). Using a multimeter, test power move by turning on/off the engine.